錐形轉子三相異步電動機（YEZ112L-4）”詳細介紹
　　YEZ系列三相錐形轉子制動異步電動機，專門與建筑機械配套而設計、制造。YEZ系列三相錐形轉子制動異步電動機，融合電機和制動器于一體，具有起動轉矩大、結構緊湊、可頻繁啟動等優點。
　　
　　YEZ系列三相錐形轉子制動異步電動機的工作特性是：定子和轉子為圓錐形，電機軸除了作旋轉運動外，還可以作軸向移動，當電機通電時，定子產生軸向磁拉力使轉子軸向移動并壓縮彈簧，使制動輪與制動座脫離，轉子旋轉；當電機斷電時，軸向磁拉力消失，在壓力彈簧的作用下，制動輪復位與制動座摩擦，實現電機的快速制動。
　　
　　YEZ系列三相錐形轉子制動異步電動機，一般采用50赫芝、380伏、B級絕緣、IP4防護等級。
　　注：R為凸緣蓋配合面至軸伸肩的距離（工作時）。
　　
　　使用與維修保養
　　1、電動機可在不低于額定電壓90％的情況下使用。
　　2、首次使用前進行一段時間的空載運轉和一定次數的反復起動和制動，無異常后才可加載使用。
　　3、電動機不可在易爆、腐蝕或其他有害氣體的環境中使用。
　　
　　4、電動機在使用中，如發現制動環磨損使制動力矩過小時，應調整風扇制動輪的相對位置，調整步驟如下：先將鎖緊螺母與風扇制動輪之間的螺釘拆下，旋緊鎖緊螺母位置，最后將螺釘擰緊，若上述調法仍不行，則應更換制動環。壓裝時，用木錘將制動環四周均勻地敲入錐面槽內，制動面斜角20°應在車床上車削后刮配，使其后端蓋剎車面接觸率不低于80％。
　　
　　5、軸承潤滑脂一般每半年更換一次，洗凈后注入鈣一鈉基潤滑脂，若軸承磨損嚴重，則按軸承規格進行更換。
　　6、在搬運電機時應小心輕放，儲存?zhèn)}庫或擱置不用的電機應妥善包裝，做好防銹措施，倉庫保持通風干燥，重新啟用電機前應用500V兆歐表測量絕緣電阻，其電阻值不低于20MΩ，否則應烘干處理。

Three phase induction motor with conical rotor (YEZ112L-4)

YEZ系列三相錐形轉子制動異步電動機，專門與建筑機械配套而設計、制造。YEZ系列三相錐形轉子制動異步電動機，融合電機和制動器于一體，具有起動轉矩大、結構緊湊、可頻繁啟動等優點。

YEZ series three-phase conical rotor brake asynchronous motor, specially designed and manufactured with the construction machinery. YEZ series three-phase conical rotor brake asynchronous motor, fusion motor and brake in one, with a large starting torque, compact structure, can be frequent start and so on.

YEZ系列三相錐形轉子制動異步電動機的工作特性是：定子和轉子為圓錐形，電機軸除了作旋轉運動外，還可以作軸向移動，當電機通電時，定子產生軸向磁拉力使轉子軸向移動并壓縮彈簧，使制動輪與制動座脫離，轉子旋轉；當電機斷電時，軸向磁拉力消失，在壓力彈簧的作用下，制動輪復位與制動座摩擦，實現電機的快速制動。

The working characteristics of YEZ series three-phase asynchronous motor is a conical rotor brake: stator and rotor is conical, in addition to the motor shaft rotate, can axially move when the motor is energized, the stator generates the axial magnetic force of the rotor axial movement and the compression spring, the brake wheel and the brake seat from the rotor to rotate; when when the electrical power, the axial magnetic force disappears, pressure in the spring under the brake wheel and the brake seat friction reduction, fast braking motor.

YEZ系列三相錐形轉子制動異步電動機，一般采用50赫芝、380伏、B級絕緣、IP4防護等級。

YEZ series three-phase conical rotor brake asynchronous motor, generally using 50 Hz sesame, 380 volts, B grade insulation, IP4 protection grade.

注：R為凸緣蓋配合面至軸伸肩的距離（工作時）。

Note: R is the distance from the mating face to the shaft of the shaft (working hours).

使用與維修保養

Use and maintenance

1、電動機可在不低于額定電壓90％的情況下使用。

1, the motor can be used in the case of no less than 90% of the rated voltage.

2、首次使用前進行一段時間的空載運轉和一定次數的反復起動和制動，無異常后才可加載使用。

2, the first use of a period of time before the no-load operation and a certain number of repeated starting and braking, no exception can be loaded after the use of.

3、電動機不可在易爆、腐蝕或其他有害氣體的環境中使用。

3, the motor can not be explosive, corrosive or other harmful gases in the environment to use.

4、電動機在使用中，如發現制動環磨損使制動力矩過小時，應調整風扇制動輪的相對位置，調整步驟如下：先將鎖緊螺母與風扇制動輪之間的螺釘拆下，旋緊鎖緊螺母位置，最后將螺釘擰緊，若上述調法仍不行，則應更換制動環。壓裝時，用木錘將制動環四周均勻地敲入錐面槽內，制動面斜角20°應在車床上車削后刮配，使其后端蓋剎車面接觸率不低于80％。

4, the motor is in use, such as found in the brake ring wear the brake torque is too small, should adjust the relative position of fan wheel brake, the adjustment steps are as follows: first lock screws between the nut and remove the fan wheel brake, tighten the lock nut screw position, finally, if the transfer method is still not. Replace the brake ring. Press the brake, with wooden hammer evenly in the cone ring around the groove, the brake surface angle 20 degrees in lathe cutting after scraping, the back end cover brake contact rate of not less than 80%.

5、軸承潤滑脂一般每半年更換一次，洗凈后注入鈣一鈉基潤滑脂，若軸承磨損嚴重，則按軸承規格進行更換。

5, bearing grease is generally replaced once every six months, wash after injection of calcium a sodium base grease, if the bearing wear serious, then according to the bearing specifications for replacement.

6、在搬運電機時應小心輕放，儲存?zhèn)}庫或擱置不用的電機應妥善包裝，做好防銹措施，倉庫保持通風干燥，重新啟用電機前應用500V兆歐表測量絕緣電阻，其電阻值不低于20MΩ，否則應烘干處理。

6, in the handling of motor should be handled with care, storage or use of the motor should be properly packed, good antirust measures, warehouse ventilation drying, re enable the motor before the application of 500V megger insulation resistance, the resistance value of not less than 20M, otherwise it should